Screw-Clamp Tripod Phone Mount
Created 13 days ago
Description
A rigid tripod mount designed to secure mobile phones for hands-free filming. The design uses a threaded screw mechanism instead of a printed spring, ensuring the clamping force remains consistent without material fatigue over time. The base includes a slot designed to capture a standard 1/4-20 hex nut for mounting to standard camera equipment.\n\nFeatures of this mount include:\n* Adjustable grip range accommodating devices from 60mm to 85mm wide.\n* Chamfered jaw faces to hold the device securely without marring the edges.\n* A captive nut slot at the base for standard 1/4-20 tripod hardware.\n* A freely spinning upper jaw pad that presses flat against the device during tightening.
Images
More like this
Explore more in Desk & Tech →
1/4"-20 Phone Ring Light Clamp
A two-piece spring clamp designed to mount a mobile phone within the center of a standard ring light for filming. The base features a horizontal captive slot sized for a 1/4"-20 hex nut, allowing direct attachment to standard tripod and ring light threads. Jaw tension is provided by looping a standard rubber band over the outward-facing anchor pegs located on the exterior of both the fixed and sliding jaws. Technical Specifications Grip Range: 60mm to 85mm horizontal capacity. Mounting Interface: 1/4"-20 pass-through with captive hex nut slot. Jaw Profile: Recessed inner faces designed to accept soft foam or rubber grip tape. Mechanism: Guided T-track slider with external tension anchors.
Heavyweight Treadmill Phone Rig
With a subtle backward tilt and a monolithic ribbed-industrial feel, this phone mount locks securely onto a 25mm treadmill rail while carrying a heavy-duty phone case. It boasts heavily chamfered outer edges—giving it a tactile, finished look—while retaining high side-walls and a formidable front guard lip. Key Dimensions Width: 72mm (with added side clearance) Depth: 24mm (plenty of room for thick cases/pop-sockets) Clamp: Sized for 25mm horizontal rails with flared, snap-fit lead lines Angle: Generous 17-degree back tilt for effortless mid-run swiping
Deep-Ledge 65-Degree Phone Stand
A rigid phone stand angled at 65 degrees, proportioned to clear lower screen content while retaining devices in thick cases. Requisite bracing is extruded into a single dimension to maintain a flat footprint and minimize material usage. Features: 24mm deeper retaining ledge for armored or wallet cases. Reduced 9mm front lip height to prevent screen obstruction. 65-degree optimal viewing incline. Rigid 6mm profile. Overall capacity accommodates devices around 3 by 7 inches.
110mm Triangular Phone Stand
A rigid phone stand with a truncated back. The overhanging vertical rest has been clipped, terminating the structure at the brace point to form a closed, structural triangle that reduces overall height while maintaining a 65-degree device angle. Parameters and capacity: Backrest Height: 110mm apex. Viewing Angle: 65 degrees from vertical. Ledge Depth: 24mm for clearance of thick cases. Frame Structure: 6mm width, extruded to 76.2mm.
1/4-20 to 3/8-16 Tripod Adapter
An adapter designed to convert a standard 1/4-20 tripod mounting screw to a larger 3/8-16 male thread. The outer diameter incorporates a textured knurled surface, allowing the component to be firmly finger-tightened or removed without the use of hand tools. Base interface: 1/4-20 female thread Top interface: 3/8-16 male thread Exterior: Knurled cylindrical grip for manual torque application Use case: Adapting standard photography tripods, light stands, or camera quick-release plates to accept heavier audio, lighting, and camera accessories
8-Slot PC Cable Comb
A rigid 8-slot cable comb designed to flatten out chaotic PC cable bundles. Spaced precisely for standard 18AWG PSU wires, it includes mounting flanges on either side to pin the whole run tight against a case wall or back panel. Remix Variables Channel Dimensions: Currently set to a 3.5mm width on a 4.5mm pitch. Expand the width to 4mm or higher if you are working with thick sleeved cables. Slot Count: Built for an 8-pin run (like a GPU or EPS cable). Extending the pattern to 24 slots for a 24-pin motherboard main power cable is a straightforward parameter update. Mounting Hardware: The end flanges are drilled for M3 screws with a simple countersink. These can easily be scaled for M4 hardware or removed entirely if you prefer mounting with double-sided tape.