1/4"-20 Phone Ring Light Clamp
Created 18 days ago
Description
A two-piece spring clamp designed to mount a mobile phone within the center of a standard ring light for filming. The base features a horizontal captive slot sized for a 1/4"-20 hex nut, allowing direct attachment to standard tripod and ring light threads. Jaw tension is provided by looping a standard rubber band over the outward-facing anchor pegs located on the exterior of both the fixed and sliding jaws.
Technical Specifications
- Grip Range: 60mm to 85mm horizontal capacity.
- Mounting Interface: 1/4"-20 pass-through with captive hex nut slot.
- Jaw Profile: Recessed inner faces designed to accept soft foam or rubber grip tape.
- Mechanism: Guided T-track slider with external tension anchors.
Images
More like this
Explore more in Desk & Tech →
Screw-Clamp Tripod Phone Mount
A rigid tripod mount designed to secure mobile phones for hands-free filming. The design uses a threaded screw mechanism instead of a printed spring, ensuring the clamping force remains consistent without material fatigue over time. The base includes a slot designed to capture a standard 1/4-20 hex nut for mounting to standard camera equipment.\n\nFeatures of this mount include:\n Adjustable grip range accommodating devices from 60mm to 85mm wide.\n Chamfered jaw faces to hold the device securely without marring the edges.\n A captive nut slot at the base for standard 1/4-20 tripod hardware.\n A freely spinning upper jaw pad that presses flat against the device during tightening.
Heavyweight Treadmill Phone Rig
With a subtle backward tilt and a monolithic ribbed-industrial feel, this phone mount locks securely onto a 25mm treadmill rail while carrying a heavy-duty phone case. It boasts heavily chamfered outer edges—giving it a tactile, finished look—while retaining high side-walls and a formidable front guard lip. Key Dimensions Width: 72mm (with added side clearance) Depth: 24mm (plenty of room for thick cases/pop-sockets) Clamp: Sized for 25mm horizontal rails with flared, snap-fit lead lines Angle: Generous 17-degree back tilt for effortless mid-run swiping
Deep-Ledge 65-Degree Phone Stand
A rigid phone stand angled at 65 degrees, proportioned to clear lower screen content while retaining devices in thick cases. Requisite bracing is extruded into a single dimension to maintain a flat footprint and minimize material usage. Features: 24mm deeper retaining ledge for armored or wallet cases. Reduced 9mm front lip height to prevent screen obstruction. 65-degree optimal viewing incline. Rigid 6mm profile. Overall capacity accommodates devices around 3 by 7 inches.
ClipLevel — Light Bar Shims
ClipLevel addresses the common issue of monitor light bars tilting upward on thick-bezel screens, projecting glare directly into your eyes. These custom wedge shims sit under the rear counterweight clip, lifting it by 8mm to pitch the light beam firmly down toward your desk. A built-in front lip hooks over the monitor's top edge to keep everything securely located without adhesive. Dimensions Footprint: 30mm wide by 20mm deep per shim. Lift Angle: Tapers up to an 8mm rise at the rear. Bezel Hook: 5mm front lip to catch the monitor edge. Print Notes Orientation: Print both shims on their flat sides. Supports: Prints entirely support-free.
110mm Triangular Phone Stand
A rigid phone stand with a truncated back. The overhanging vertical rest has been clipped, terminating the structure at the brace point to form a closed, structural triangle that reduces overall height while maintaining a 65-degree device angle. Parameters and capacity: Backrest Height: 110mm apex. Viewing Angle: 65 degrees from vertical. Ledge Depth: 24mm for clearance of thick cases. Frame Structure: 6mm width, extruded to 76.2mm.
1/4-20 to 3/8-16 Tripod Adapter
An adapter designed to convert a standard 1/4-20 tripod mounting screw to a larger 3/8-16 male thread. The outer diameter incorporates a textured knurled surface, allowing the component to be firmly finger-tightened or removed without the use of hand tools. Base interface: 1/4-20 female thread Top interface: 3/8-16 male thread Exterior: Knurled cylindrical grip for manual torque application Use case: Adapting standard photography tripods, light stands, or camera quick-release plates to accept heavier audio, lighting, and camera accessories