30mm Knurled Mushroom Drawer Knob
Created 2 months ago
Description
A mushroom-profile knob designed for drawers and cabinets. The exterior cap band features a textured knurl to ensure grip when handled with wet fingers, making it suitable for kitchen or bathroom environments. An M4 clearance hole runs centrally through the entire assembly for hardware installation.
Dimensions & Fitment
- Cap diameter: 30mm
- Overall cap height: 18mm
- Stem diameter: 12mm
- Fastener compatibility: Continual M4 through-hole
- Grip profile: Knurled outer margin
Images
More like this
Explore more in Home & Fixtures →
19mm Cross-Hatch Cane Tip
A replacement tip for standard 19mm cane tubes. Designed to be printed in stiff TPU, this part replaces worn tips to eliminate floor clacking and restore grip on wet surfaces. The part features a solid tapered body and aggressive bottom channelling to handle regular outdoor and indoor use: Mounting socket: 19.5mm inner diameter and 25mm deep, featuring an entry chamfer to guide the tube. Base profile: 40mm wide contact area tapering directly to the upper shaft. Tread pattern: 4mm deep and 3mm wide cross-hatch channels to displace water and maintain floor contact.
22mm Shower Bracket Replacement Cup
What it's for A functional structural replacement for perished rubber friction cups commonly found in standard hand shower brackets. Instead of relying on a completely flexible rubber body, this cup utilizes four printed internal ridges to create a secure friction fit against a standard 22mm shower head ball end. Dimensions Inner Diameter: 22.5mm Internal Depth: 30.0mm Outer Diameter: 27.5mm Overall Height: 32.5mm Wall & Base Thickness: 2.5mm Materials Because this part is exposed to continuous heat, moisture, and mechanical stress, PETG, ABS, or a rigid TPU (like 95A) are highly recommended. PLA may soften or deform under hot water temperatures. Remix ideas Bracket sizing: Adjust the primary outer diameter and wall thickness to match the cavity of your specific wall-mounted bracket housing. Mounting holes: Add a central clearance hole or countersink to the base if the original cup was secured with a screw. Friction tweaking: Alter the radius of the four internal ridges to tune the grip strength on the 22mm shower head.
Tactile Modernist Cabinet Pull
A sleek, minimalist touch for contemporary interiors. This cabinet handle pairs a clean, soft-edge cylindrical profile with a thoughtful finger scoop carved into the underside. Designed to meet the hand naturally, the bar aligns effortlessly with modern design sensibilities, offering a refined and tactile grip that elevates everyday cabinetry. Hardware Specifications Standard Mount: 96mm screw centers for easy retrofitting or new installations Total Footprint: 130mm overall length Clearance: 35mm standoff from the cabinet face Profile: 16mm diameter featuring an ergonomic under-scoop
8.5mm Rod Square Drop-On Sleeve
Square profile sleeve that slips onto a toilet roll holder rod to increase rolling friction, deterring toddlers from unspooling the paper. Fitment: 8.5mm diameter holder rods Outer Profile: 25x25mm square, 90mm tall Installation: Direct drop-on over the existing rod Note: Make sure to check your holder's rod diameter before printing. Prints upright without supports; PETG is recommended for durability.
Geriffelte Pilzkopf-Schraubenkappe
Diese aufschraubbare Kappe verdeckt scharfkantige Holzschrauben, die aus Brettern oder Platten herausragen. Die Form erinnert an einen klassischen Drehknopf und bietet durch die seitlichen Aussparungen sicheren Halt beim Festziehen. Selbstschneidend: Das innere Loch ist konisch geformt (4,2 mm unten, 3,0 mm oben). Das grobe Gewinde der Holzschraube frisst sich beim Aufdrehen von selbst fest. Sicherer Abschluss: Entschärft gefährliche Spitzen und verhindert Kratzer. Druckfertig: Benötigt keine Stützstrukturen, druckt flach auf dem Druckbett.
Roll spinning slower - 25mm Toilet Roll Drop-On Sleeve
A 25mm diameter sleeve that slips over a standard 9.5mm toilet roll holder to increase rolling friction and deter toddlers from unspooling the roll. Dimensions: 90mm tall, 25mm outer diameter Fitment: 9.5mm central bore with a matching 9.5mm side slit for direct drop-on installation Use: Prints upright. PETG recommended for durability, though PLA is sufficient for a drop-on fit without flexing.