Aquarium Plant Stem Weight
Created 12 days ago
Description
What it's for
This flat, disc-shaped weight anchors live aquarium plants into the substrate. The design features a narrow side-entry slot that leads to a slightly wider central resting hole, allowing stems to be securely trapped without being crushed. It is ideal for newly planted aquascape stems that have not yet developed a stable root system.
Dimensions
- Overall footprint: 25mm in diameter and 8mm thick.
- Entry slot: 2.5mm wide, running from the edge to the center.
- Center hole: 4mm diameter clearance to accommodate typical aquatic plant stems safely.
Remix ideas
- Increase the overall thickness to provide more anchoring mass for highly buoyant plants.
- Widen the entry slot and center hole to accept thicker stem varieties.
- Change the outer shape from a cylinder to a square or hexagon to pack multiple weights tightly together in dense planting zones.
Images
More like this
Explore more in Home & Fixtures →
8.5mm Rod Square Drop-On Sleeve
Square profile sleeve that slips onto a toilet roll holder rod to increase rolling friction, deterring toddlers from unspooling the paper. Fitment: 8.5mm diameter holder rods Outer Profile: 25x25mm square, 90mm tall Installation: Direct drop-on over the existing rod Note: Make sure to check your holder's rod diameter before printing. Prints upright without supports; PETG is recommended for durability.
Geriffelte Pilzkopf-Schraubenkappe
Diese aufschraubbare Kappe verdeckt scharfkantige Holzschrauben, die aus Brettern oder Platten herausragen. Die Form erinnert an einen klassischen Drehknopf und bietet durch die seitlichen Aussparungen sicheren Halt beim Festziehen. Selbstschneidend: Das innere Loch ist konisch geformt (4,2 mm unten, 3,0 mm oben). Das grobe Gewinde der Holzschraube frisst sich beim Aufdrehen von selbst fest. Sicherer Abschluss: Entschärft gefährliche Spitzen und verhindert Kratzer. Druckfertig: Benötigt keine Stützstrukturen, druckt flach auf dem Druckbett.
Roll spinning slower - 25mm Toilet Roll Drop-On Sleeve
A 25mm diameter sleeve that slips over a standard 9.5mm toilet roll holder to increase rolling friction and deter toddlers from unspooling the roll. Dimensions: 90mm tall, 25mm outer diameter Fitment: 9.5mm central bore with a matching 9.5mm side slit for direct drop-on installation Use: Prints upright. PETG recommended for durability, though PLA is sufficient for a drop-on fit without flexing.
AquaDart — Garden Hose Nozzle
AquaDart introduces a streamlined approach to targeted water pressure. This single-piece nozzle adapts a standard garden hose down to a precise 0.2-inch exit stream. The internal geometry is specifically contoured to accelerate water smoothly, while the exterior features deep grooves for secure hand-tightening even when wet. Dimensions Overall height: 63 mm Base diameter: 38 mm (at the grip) Exit bore: 5.08 mm (0.2 inches) Interface: Standard 3/4" Female Garden Hose Thread (11.5 TPI) Compatibility & Usage Designed to thread directly onto standard North American garden hoses and spigots. Requires a standard rubber hose washer to sit on the internal ledge. Without the rubber washer, standard garden hose threads will leak under pressure. Print Notes Prints completely completely upright and support-free as oriented. Thick walls (4+ perimeters) and 100% infill are heavily recommended to contain the water pressure and prevent layer separation. PETG or ABS is preferred if this will be left outdoors in the sun.
Under-Shelf LED Routing Corner
A 25mm right-angle block designed to route under-shelf LED strips cleanly around inside corners without kinking. It guides the strip through a 90-degree arc inside a 10.5mm wide, 4mm deep channel, with flat back faces meant for simple adhesive mounting against the shelf walls. Remix Hooks & Constraints Wall Offset: The block's 25x25mm footprint sets the center of the strip exactly 12.5mm from both walls. Changing the block's footprint will let you shift the lighting closer to or further from the front edge of the shelf. Channel Clearance: The 10.5mm width seats a standard bare 10mm LED strip. If you swap to waterproof IP65 strips with heavy silicone doming, this channel needs to be widened to 12.5mm to avoid pinching the arc. Mounting Strategy: The current design relies entirely on flat surfaces for double-sided tape or VHB. An obvious variant for rougher wood shelves is adding a pair of 3mm countersunk holes on the mounting faces.
22mm Shower Bracket Replacement Cup
What it's for A functional structural replacement for perished rubber friction cups commonly found in standard hand shower brackets. Instead of relying on a completely flexible rubber body, this cup utilizes four printed internal ridges to create a secure friction fit against a standard 22mm shower head ball end. Dimensions Inner Diameter: 22.5mm Internal Depth: 30.0mm Outer Diameter: 27.5mm Overall Height: 32.5mm Wall & Base Thickness: 2.5mm Materials Because this part is exposed to continuous heat, moisture, and mechanical stress, PETG, ABS, or a rigid TPU (like 95A) are highly recommended. PLA may soften or deform under hot water temperatures. Remix ideas Bracket sizing: Adjust the primary outer diameter and wall thickness to match the cavity of your specific wall-mounted bracket housing. Mounting holes: Add a central clearance hole or countersink to the base if the original cup was secured with a screw. Friction tweaking: Alter the radius of the four internal ridges to tune the grip strength on the 22mm shower head.