16-Slot SD and MicroSD Wallet
Created 2 months ago
Description
This is a flat-layout combo wallet designed to organize memory cards for multi-camera setups. It holds 16 cards in total, featuring embossed numbering next to every slot to easily track which card belongs to which specific camera. Finger cutouts are positioned at the base of each slot to facilitate quick and easy removal of the media.
What it's for
Built for photographers and videographers managing multiple recording devices, this tray keeps media separated and identifiable. The engraved numbers allow for a direct mapping system between the storage slot and the specific camera body the card was pulled from.
Dimensions
- Standard SD slots: 8 slots measuring 33 x 25 x 2.5 mm.
- MicroSD slots: 8 slots measuring 12 x 16 x 1.5 mm.
- Standardized spacing with integrated access notches for bare cards.
Remix ideas
- Add a snap-fit or hinged lid to create a fully enclosed travel case.
- Modify the layout to swap some microSD slots for CFexpress or other specialized camera media.
- Deepen the slots to accommodate protective plastic snap-cases rather than bare memory cards.
Images
More like this
Explore more in Storage & Organization →
4-Slot 18650 Battery Carrier
A rugged storage block designed to carry four 18650 cells side-by-side. The flush-profile sliding lid incorporates a captive tab-lock mechanism that prevents accidental opening during transport. Actuating the latch requires sequential inward and rearward thumb pressure, ensuring the contents remain secure even when loose inside a crowded tool bag. Capacity: 4x 18650 batteries Cell Fitment: Oversized slots (19.5mm diameter x 66.5mm length) to accommodate longer protected cells Closure: Sliding track lid with an integrated flush thumb-release lock Profile: Flat parallel array for low-profile tool bag pocket stowage
Hinged Lockbox with Access Port
A heavy-duty electronics or utility enclosure featuring a hinged lid and a front-facing access port. Designed to be printed entirely without supports, the lid is oriented flat on the build plate and attaches to the main body via a simple filament-pin hinge. A pair of aligned tabs at the front accommodate a standard small padlock or zip tie for securing the contents. Specifications Overall Dimensions: 150mm (W) x 80mm (D) x 100mm (H) Wall Thickness: 3mm Access Port: 45mm diameter, positioned with a 20mm clearance from the inner floor. Hardware Required: 1.75mm filament scrap or 2mm metal rod for the hinge pins; small padlock for the front tabs.
30mm Print-in-Place Hinged Box
A compact, support-free storage case designed to print as a single assembled unit. The clamshell design lies flat on the build plate, using internal conical pins to create a working 180-degree hinge straight off the printer. Dimensions: 30mm square footprint when closed; 20mm total height. Mechanism: Integrated conical barrel hinge with 0.4mm clearances. Closure: Friction-fit horizontal snap ridge on the front lip. Print Setup: Requires no supports. Best printed in PLA or PETG with standard 0.2mm layer heights.
Wall mount TV remote bracket for narrow remotes
A sleek, vertical cradle designed to keep the television remote permanently anchored next to the light switch. Sized specifically for a 160×50×22mm controller, the sleeve wraps the remote securely while leaving a generous front window to let you grab it without scraping your knuckles against the wall. Design Notes Friction Fit: Built with a 51×24mm interior channel to give a 50×22mm remote a smooth glide without rattling. Access Window: The front face is cut wide open, leaving a 10mm lip around the bottom and sides to lock the remote in place while keeping the buttons visible. Flush Mounting: Features two countersunk M3 screw holes spaced vertically, ensuring the screw heads sit dead-flush against the back wall and won't scratch your plastic.
Optic — Bedside Glasses Perch
The Optic is a dedicated resting place for your reading glasses, designed to keep them safe from accidental crushing on the nightstand. Shaped with a gentle taper that mimics the geometry of a face, it features a specialized 18mm wide nose bridge at the peak. A transverse saddle trench ensures the glasses seat securely and naturally, allowing the lenses to rest against the sloped front without sliding off. Features Anatomical Fit: 18mm nose bridge precisely matches standard reading glasses. Secure Saddle: Transverse cutout catches the frame bridge to prevent slipping. Stable Base: Wide footprint resists tipping when retrieving your glasses in the dark.
Coarse Thread 60mm Storage Jar
What it's for A rapid-access cylindrical container designed to cleanly organize loose hardware and replace makeshift storage like repurposed jam jars. Driven by a coarse 8-pitch thread, the lid seats completely in a single rotation for rapid open and close cycles. The flush-fit lid features deeply recessed perimeter channels to provide mechanical grip, making it well-suited for repetitive workshop tasks or kitchen spice organization. Dimensions Overall footprint: 60 mm exterior diameter x 70 mm total height Interior capacity: 55 mm internal diameter in the main body Mouth opening: 45 mm internal, dropping straight into the cavity Thread specification: 50 mm diameter neck with an 8 mm pitch Remix ideas Add internal intersecting dividers to isolate different sizes of washers and screws. Cut a shallow recess into the lid top and a matching rim on the jar bottom for vertical stacking. Embed an angled slot on the external shell face to hold paper labels or masking tape.